First Post About Naomi

Family Picture

I’m so happy to announce that our daughter was born!… Last year! I’ve been thinking about how to post about my family on the Internet because, well, it’s the Internet. So for now we’ll just write about her and share some of the things we’ve learned and the joys and angst.

Naomi and Daddy

Naomi is a joy, that’s what I tell everyone. She has a really good attitude, for the most part she’s very happy and she shares it. I love to watch her and see her learning. Lately she’s been watching our hands, so we clap wiggle our fingers, make a fist and mime picking up Cheerios with our “pincers”. Naomi takes it all in and laughs with the joy of it. When we put her down for a nap she’ll coo (and sometimes screech, like right now as I write). When Sara rubs noses with her, Naomi will giggle and smile. She loves to read books, play peek-a-boo, hearing Sara and I sing, and fabrics. She does not like having gas, being hungry, and/or getting her arms into tight shirts!

We’ve learned that we can keep a baby alive! Well, that sounds dramatic but never have I been more scared than leaving the hospital after Naomi was born. I must looked like a lost puppy to the wonderful nurses who encouraged us the whole time we were there. We are so thankful for all their help. Patience is key, and I’ll never finish all the stuff I want(/need) to do in a timely fashion. (I still haven’t sent my father a Father’s Day card, sorry Dad.) I’ve learned how to dress a baby, feed her and all the while keep up with dishes, work and whip up some tasty meals too.

Naomi gumming on a clementine

We’ve struggled with different expectations as parents, how to configure the boat for a baby and (of course) when Naomi cries. Lately she’s been “finding her voice” and what a voice she has! Sometimes getting her to sleep is challenging and we spend lots of time trying to help her fall asleep. Dirty diapers and garbage. Our trash has at least doubled.

I’m amazed with our child. She’s been sailing seven times since she was born (one of those was on a motorboat). She’s been on six flights. (Maybe we can get her on a train and she’ll have traveled on Planes, Trains and Automobiles). We’re teaching her to swim, talk, crawl, eat and probably a whole lot else that we’re not even aware of. We love her and really look forward to seeing her grow and become who she’s going to be.

Lion King Naomi

Saying Good-bye and Hello

A lot of people have asked us whether we’re looking for a land house now that we’re pregnant. It’s a fair question. There are a lot of considerations when thinking about raising a child (or children) on a boat. How many little PFDs are we going to need, where do you change diapers, for that matter where do you store diapers?

But… we haven’t considered going back to land. There is so much about this life that we love. Nothing beats coasting through the water with nothing but the sound of the waves against the hull and the wind in the sails. Or gently swinging at anchor doing some boat task while the sun sets.

The only thing is that Hiraeth is small with a 30 foot LOA and 9.8 foot beam, no quarter berth, just a comfy saloon, small head and a v-berth. We were prepared to stay in her regardless but an opportunity landed in our laps and we decided to jump.

We bought a Catalina 34 and sold our Alberg 30, Hiraeth. The Catalina 34 is named Adrenaline, she’s in pretty good condition and we’re already jumping into various customization and improvements. Can’t wait to share more about that later!

Hauled out for a bottom job
Hauled out for a bottom job and survey

So it’s a good-bye and a hello. We’re working hard to make her ready for the baby and be a good home for us for the foreseeable future!

Exciting Announcement

I’m afraid I haven’t had as much time to devote to the blog this past year. We’ve been a little busy…

New Crew Arriving November 2018
New Crew Arriving November 2018

Merry Christmas

Merry Christmas from Florida here on Hiraeth. We had some awesome fog the morning of Christmas Eve.

Socked in Marina
Socked in Marina

Fishing Vessel in Fog
Fishing Vessel in Fog

Christmas Eve service hosted by Bridge Point Church at the Mahaffey Theater. We walked back with Sarah, John and Susan.

Walking from Christmas Eve Service
Walking from Christmas Eve Service

The service was quite a production. That night we joined some friends from college who even put together some stockings for us so we could join in with their family! Thanks Matt and Shannon!

Opening Stockings
Opening Stockings

Christmas day we enjoyed a nice walk along the waterfront before joining James and Robin and friends aboard S/V Sarita Sea for homemade gumbo and New Orleans boudin.

Celebrating Christmas with Friends
Celebrating Christmas with Friends

Trying Boudin
Trying Boudin

A very nice Christmas here in Florida. Without the snow it didn’t really feel like Christmas until the day’s festivities. But still I’m thankful for the season and to celebrate Christ’s birth.

Head Repair

I think nearly every sailing blog has a post (or two) on the topic of head repair. When living on land I take for granted that when I flush the toilette my waste simply goes away. I only have to think about it when the water/sewer bill comes due (or when I have to dig up the tank to be pumped.) Aboard it’s probably a weekly issue and if the head is acting up… Ain’t nobody happy.

Anyway, my head had been leaking for a few months and it was finally time to sit down and see what the problem was. I have a Raritan PHII manual pump marine toilette and I’ve heard good things about it. It seemed pretty easy to disassemble. In preparation I also bought the rebuild kit. So I got started.

Pump Housing - Before
Pump Housing – Before

After completely disassembling the unit Sara and I cleaned all the parts and installed all the new o-rings and seals from the rebuild kit.

Cleaning the Pump
Cleaning the Pump

While cleaning the pump housing I discovered the crack which was the cause of the leak.

Cracked Pump Housing
Cracked Pump Housing

I called around but no one carried the pump housing. Ordering one would take at least two days so I decided to use some 3M 4000 adhesive sealant that I had in my toolbox. I applied the sealant on the inside and outside of the pump.

Sealed Pump Housing
Sealed Pump Housing

Finally I assembled everything and tested the pump.

Reassembled Pump
Reassembled Pump

Sure enough it worked like a charm. Now we’ll wait to see how long my sealant hack works. I should probably order the pump housing now to have it if and when the sealant breaks down. Here’s hoping it lasts a good long time!

Head Repairs
Head Repairs

Thanksgiving Cruise

Sara and I returned from our trip to the Great White North. (More on that later.) We were relieved to find that Hiraerth had survived Hurricane Irma without a single scratch inside or out. The next two weeks were a whirlwind as we recommissioned systems, addressed an issue with our head, reconnected with old friends and met new people on the docks.

Slow Sail toward the Skyway Bridge
Slow Sail toward the Skyway Bridge

We departed on a cold, cloudy day with a light north wind. We weren’t in a hurry so we pulled out only the jib and sailed down to the Manatee River where we anchored with some of our new friends Chasseur and Luf-fin Place. That night we enjoyed games and each others company as we got to know each other.

Chasseur
Chasseur

The next day we all dinghied to shore and walked to the lookout tower in Emerson Point Preserve. It was a fun walk and a great view. Then we all turned our bows to Longboat. On the bay we had pretty light winds and were again sailing downwind. I poled out the jib and was making 3 knots wing-on-wing. Finally we turned into the ICW and motored the rest of the way.

That night we went to the beach and enjoyed twilight. It was beautiful.

Twilight at Longboat Beach
Twilight at Longboat Beach

Luf-fin Place
Luf-fin Place

Saturday we parted ways. Luf-fin Place headed back to the Marina, Chasseur stayed at anchor and explored Longboat. Sara and I headed out to the Gulf and sailed up to the mouth of Tampa Bay. Then we motored the rest of the way up to Pinellas Point for our last night at anchor.

Sailing Up the Gulf
Sailing Up the Gulf

The next day with wind and swell on the nose we trudged back up to the Marina ourselves. Next up, working and more boat projects!

Big Sarasota Grounding

The day started well. We left Pelican Bay, Cayo Costa, just west of Fort Myers, Florida, at 0630 for the best tides. Our safety inlet was Venice which we reached around 1245. It was a nice sail with east-northeast winds around ten knots. I kept the motor running to boost our speed since we wanted to get to Sarasota, if possible. Our goal that day was Big Sarasota Pass (NOAA chart 11425), a wide body of water but shallow. When I looked at the charts, it was apparent that we would be able to get in from the west but it would be close. I also called Sea Tow for their opinion of the inlet. They said that with a four and a half foot draft we’d be fine. Find marker six and approach at forty degrees.

As I looked across the water, I couldn’t find red six, but I could find eight! The tide was high and I felt confident that we’d have more water than what was on the chart. We prepared to turn in. Sara went up to the bow to watch the water. All goes well for three minutes then the water got skinny quickly. First the shallow water alarm went off. At this point I knew there was about a foot and a half of water under the keel. I didn’t turn back as I was confident in the charts. Then suddenly bump… bump. Crap! Sara started to run back to the cockpit and yelled, “We touched bottom!”
I quickly shifted to neutral and hauled the dinghy in from behind us and shifted again to reverse. After about thirty seconds, we were still bouncing on the sandbar and unable to back off. Next, I had Sara push out the boom and I went forward with the tiller hard to port thinking I may be able to heel Hiraeth and use the engine to push us around. We made a little progress but not enough. We were hard aground and I wasn’t going to be able to get us off with the motor.

The water was getting rough with an east wind that was starting to kick up. To be safe I called TowBoatUS for the first time to make use of my unlimited towing. The dispatcher indicated that the towboat would be on site in forty-five minutes to an hour! Well, the tide was going out now, so I knew it was just going to be harder to pull us off. I didn’t want to be bouncing of the sandbar for an hour. I decided to attempt to kedge off.

Sara and I put the outboard on the dinghy and piled in one hundred fifty feet of rode and the bruce anchor. I motored out to deeper water and tossed the anchor overboard then raced back to Hiraeth and hastily tie up the dinghy (more on this later.) Sara told me while I was out that the Coast Guard just issued a thunderstorm warning with thirty knot winds and dangerous lightning. They recommended keeping an eye out for water spouts! Perfect. The anchor rode went through the bow chock, we wrapped it around the mast winch and started cranking it in. We cranked and cranked.Hauling Hiraeth off the Sand Sara tailed for me and we just kept cranking. Fifteen feet, thirty, crank, crank, forty-five… bouncing along then something felt different. We were starting to come off the bar!

Sara not wanting my arms to cramp up recommended trying to motor off. I thought that was a great idea (while still supremely confident in my stamina). I went to the cockpit and put it in forward. Sure enough we bounced along a little longer and then we were off! Sara was hauling in anchor line like a mad woman. Soon there was only fifty feet of rode out and all of the sudden the engine stopped cold. It didn’t sputter or cough, it just died.

I won’t repeat the words that ran through my mind just then. What could have happened? I tried to start it up again but of course there was nothing. I thought maybe the anchor rode somehow got caught up in the prop. Then I saw the bitter end of the dinghy painter pulled taught on the toe rail and I knew what happened. Darn it!

Well, we were still anchored and the wind was blowing us away from the bar. So as powerless as I felt, at least weren’t going to be blown back into nearby sandbars. I thought about jumping in and untangling the painter but the sea state was pretty rough and the lightning had us a little leery about going in the water under the transom. Since TowBoatUS was already on the way, we decided to sit still and let him tow us in.Being Towed through Big Sarasota Pass

It was a good thing we did because I don’t think I could have found the safe water through the pass on my own. Our charts were completely wrong. Finally the towboat captain brought us to safety where we tied up to a mooring ball for the night. The next morning I dived in and cut away the offending dinghy painter. I checked the engine and was able to start her right up. Amazing.Diving on the Propeller

Lessons learned:

  1. Don’t trust your charts in these inlets!
  2. Corollary, trust your depth sounder!
  3. Don’t be in such a rush you lose track of your dinghy painter.

Icebox Upgrade Part 2

Where were we? Ah yes, installing the insulation.

Second layer of insulation
Second layer of insulation

I have two layers of one inch thick R-5 XPS insulation covered in a watertight radiant barrier. This will give me R-10 for the box (hopefully the original foam will add something too since it’s still there.) The last piece to go in is the top of the icebox with resin covered plywood blocks stacked up to provide a solid mounting point for the holding plate.

Top layer with mounts for the holding plate
Top layer with mounts for the holding plate

With all the insulation in place next I add the FRP liner.

FRP liner to protect the insulation
FRP liner to protect the insulation

I put a PVC pipe through the hole for the coolant tubes and used Marine-Tex as a sealant around the seams.

Marine-Tex and PVC pipe
Marine-Tex and PVC pipe

The rest of the seams taped for easier sealing
The rest of the seams taped for easier sealing

Finally uncoil the tubes and slide the holding plate into place. I make it sound easy, it was anything but. After stripping heads of multiple screws and snapping off a drill bit inside the counter top I finally got the holding plate secured to the roof of the box.

Holding plate secured
Holding plate secured

Next I installed the compressor in the cockpit locker and put the control panel in the bulkhead above the icebox.

Control panel installed
Control panel installed

Closer look at the control panel
Closer look at the control panel

Finally to test it out!

Compressor running and holding plate chilling!
Compressor running and holding plate chilling!

Now what to do about the pitted and ugly fiberglass frame around the lid? Well I’ll keep going with the Marine-Tex.

Cleaning up the frame for the lids
Cleaning up the frame for the lids

Sand it down
Sand it down

Finish with paint
Finish with paint

I replaced the insulation in the lids and painted them too.

Before
Before

Lids insulated and painted
After

I’ve been running it for a couple days now and the results are good but not great. The system is very efficient. During the day the solar panel provides all the power it needs to run in freeze mode where the holding plate is charged up (or should I say down) to seven degrees Fahrenheit. At night the unit runs in economy mode where the holding plate is maintained between twenty and thirty degrees. However the temperature in the box doesn’t drop as low as I’d like it. It fluctuates between forty-three and forty-eight degrees.

Icebox keeping cold!
Icebox keeping cold!

I’ll have to run some more tests and see if I can get the temperature closer to freezing. The Isotherm unit has an automatic mode which is what I’ve been using to maintain the greatest efficiency. It also has a manual mode which I’ll try to use to see if I can lower the temperature of the box.

Icebox Upgrade!

What have I been up to lately? Well, let’s see what it looks like…

Icebox with lid support cut out
Icebox with lid support cut out

Cutting out shelf supports in the box
Cutting out shelf supports in the box

Cutting out foam insulation and fitting it into the box
Cutting out foam insulation and fitting it into the box

All the insulation with radiant barrier prepared for adhesion
All the insulation with radiant barrier prepared for adhesion

Radiant barrier glued to the insulation
Radiant barrier glued to the insulation

Hole in the insulation for holding plate tubes
Hole in the insulation for holding plate tubes (edges taped)

First layer of insulation glued into the box
First layer of insulation glued into the box

Isotherm holding plate and condensing unit
Isotherm holding plate and condensing unit

I’m pretty excited about getting this icebox upgraded to a refrigerator!

Garmin Tracks

I’ve been trying to figure out how to get all our Garmin tracks on one Google Map and I think I’ve finally figured out how using a tool called GPSBabel to reduce the number of points on each track and then merge them together. Here’s the result with a few pictures embedded as well.